POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM MANUAL
POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM FULL
POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM CODE
POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM PROFESSIONAL

Zodiac В® pool equipment is pressure tested at the factory. These requirements are generally not intended to apply to the pool equipment such as filters or pumps. Local codes may require the pool piping system to be subjected to a pressure test. To minimize the risk of severe injury or death the filter and/or pump should not be subjected to the piping system pressurization test. Be sure all air is out of the system before operating. Trapped air in system can cause the filter lid to be blown off, which can result in death, serious personal injury, or property damage.Do not connect the system to an unregulated city water system or other external source of pressurized water producing pressures greater than 35 PSI.Incorrectly installed equipment may fail, causing severe injury or property damage. Copies of the NEC may be ordered from the National Fire Protection Association В® (NFPA В®) online at or call 61, or contact your local government inspection agency.

POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM CODE

Disconnect the pump and have the problem corrected by a qualified service representative before using.Дue to the potential risk of fire, electric shock, or injuries to persons, Zodiac Pumps must be installed in accordance with the National Electrical Code В® (NEC В®), all local electrical and safety codes, and the Occupational Safety and Health Act (OSHA В®). If the GFCI interrupts power to the pump without the test button being pushed, a ground current is flowing, indicating the possibility If the GFCI fails to operate in this manner, the GFCI is defective. Make sure such a GFCI should be provided by the installer and should be tested on a routine basis. Contact a qualified electrician if you cannot verify that the circuit is protected by a GFCI. Connect only to a branch circuit that is protected by a ground-fault circuit-interrupter (GFCI). RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY, OR DEATH. Zodiac В® pumps are powered by a high voltage electric motor and must be installed by a licensed or certified electrician or a qualified swimming pool service technician.

POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM FULL

To reduce the risk of property damage or injury, do not attempt to change the backwash (multiport, slide, or full flow) valve position with the pump running. To reduce the risk of injury, do not permit children to use this product. When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: Polaris В® PB4-60 Booster Pump | Installation and Operation ManualДЄll electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. 16Д§.3 Pump Dimensions.Д§.4 Visual Identification of the New Polaris PB4-60Д«ooster Pump. Replacement Parts List.Д§.2 Polaris PB4-60 Booster Pump Exploded View. Product Specifications and Techni-Д¬al Data.

Service Technician Maintenance.Д«locked Impeller. Installation Recommendations.ДЈ.3.6 Check the Water Flow.Д¬onduct Pressure Test. Д«onding and Grounding.Д®lectrical.Д®lectrical Wiring. This information should be given to the owner/operator of this equipment.

POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM MANUAL

If these instructions are not followed exactly, a fire or explosion may result, causing property damage, personal injury, or death.ДЄTTENTION INSTALLER: This manual contains important information about the installation, operation and safe use of this product. Improper installation and/or operation will void the warranty. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Before installing this product, read and follow all warning notices and instructions that accompany this product.

Improper installation and/or operation can create dangerous electrical hazards, which can cause high voltages to run through the electrical system.

POLARIS PB4 BOOSTER PUMP WIRING DIAGRAM PROFESSIONAL

In the event no such state or local requirement exists, the maintainer must be a professional with sufficient experience in pool equipment installation and maintenance, so that all of the instructions in this manual can be followed exactly. FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed, where such state or local requirements exist.

Polaris pb4 booster pump wiring diagram